Enviro Westport C-11290 Bedienungshandbuch

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R I E S

10of the sheet metal straps back towards the vent cap, so the decorative wall thimble will conceal it (see left image in Figure 9).STEP 7. Sl

Initial InstallationQUALIFIED INSTALLERS ONLYVERTICAL INSTALLATION:STEP 1. Check the instructions for required clearances (air spaces) to combustible

Initial InstallationQUALIFIED INSTALLERS ONLYVerticalTerminationStorm CollarFlashingRoofing nailsElbow Strapthe exposed sections, bend the support

13STEP 8. Continue to add pipe sections until the height of the vent cap meets the minimum code requirements. Refer to Figure 16 and Table 3.

Initial InstallationQUALIFIED INSTALLERS ONLYCATHEDRAL CEILING INSTALLATION:Figure 19: Cathedral Ceiling Support Box Leveling.Figure 20: Cathedral Cei

15INSTALLATION INSTRUCTIONS:1. Decide on a location for the unit that will meet any or all local code requirements. Refer “Planning

Figure 23: Assembly of Venting Kit.Initial InstallationQUALIFIED INSTALLERS ONLY     

17Initial InstallationQUALIFIED INSTALLERS ONLYVENTING INTO A CLASS ‘A’ CHIMNEY:This model is also certied and tested to vent into CLASS ‘A’ wood sto

Initial InstallationQUALIFIED INSTALLERS ONLY             

19Initial InstallationQUALIFIED INSTALLERS ONLYINSTALLATION OF TOP VENTED; HORIZONTAL TERMINATION:This is the most common type of installation style.S

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must be

FREESTANDING DRAFTHOOD ADAPTOR:This Drafthood Adaptor is a complete assembly and is ready to t onto your Westport in a vertical vent application only

21GENERAL VENTING INFORMATION:Canadian InstallationsThe venting system must be installed in accordance with the current CSA B149 installation code and

AUTOMATIC SAFETY SHUT DOWN:If the spill switch is activated and shuts off the main burner the following procedure should be followed.• Is the pilot a

VentRestrictorPositions543210’(0 m)0’(0 m)5’(1.52 m)5’(1.52 m)10’(3.05 m)10’(3.05 m)15’(4.57 m)15’(4.57 m)20’(6.10 m)25’(7.62 m)30’(9.14 m)18’(5.49 m)

Initial InstallationQUALIFIED INSTALLERS ONLYELECTRICAL REQUIREMENTS FOR GAS VALVE AND OPTIONAL BLOWER:

25Initial InstallationFUEL CONVERSION:WARNING: This conversion kit shall be installed by a qualied service technician in accordance with

26Natural Gas PropanePilot Orice .62 mm .35 mmBurner Orice Top #39 DMS #53 DMSVenturi Setting1/16” min.3/16” min.Table 5: Orice Information.STEP 9.

Initial InstallationGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the necessary gas co

28Secondary InstallationINSTALLATION OF LOG SET AND EMBERS:The placement of the logs is not arbitrary. If they are positioned incorrectly, the a

Secondary InstallationCAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED.Important note: When the unit is turned on for the r

Table of Contents3Safety Precautions...2Table of Contents...

30Secondary InstallationINSTALLATION OF PANEL SET:The brick panel set is fragile. Handle panels with care and avoid knocking them on the placement pin

Operating InstructionsFOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION M

32Routine Maintenance and ServicePeriodically check to ensure that your system is clean.Periodically check the pilot and burner. Check to see that all

Routine Maintenance and Service CLEANING THE INSIDE OF THE FIREBOXTurn off the unit and allow it to cool down completely.Remove the log carefully from

Trouble ShootingProblem Possible Cause SolutionSpark will not light the pilot after repeatedly pressing the spark ignitorDefective piezo ignitor. • Ch

Referance Number Part Description Part Number1 Top Vent Insert Piece - Painted EGWP-5031 Top Vent Insert Piece - Antique White EGWP-503AW1 Top Vent In

36Referance Number Part Description Part Number6 Cast Leg (Each) - Painted EGWP-5086 Cast Leg (Each) - Antique White 50-3756 Cast Leg (Each) - Diamond

Parts Diagram - CastWestport CastingsJune 200437

38Parts List - ComponentsReferance Number Part Description Part NumberConversion Kit LP to NG (Top & Rear Vent) 30-001Conversion Kit NG to LP (Top

Parts List - ComponentsReferance Number Part Description Part NumberDrafthood Adapter 50-84123 3 Flame Pilot Hood 50-925Owner’s Manual 50-1033Brick Pa

4Codes And ApprovalsDIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its’ air for combustion from outside the dw

40Parts Diagram - ComponentsWestport BodyJune 2004

41WarrantySherwood Industries Ltd. offers a Limited Lifetime Warranty on this gas product. This limited lifetime warranty covers the appliance for a p

42Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

5WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoni

1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.2 In accordance with the current ANSI Z223.1 NFPA 54, National Fu

7VENT PARTS:This replace have been tested and certied for use with SIMPSON DURAVENT TYPE GS PIPE FOR GAS STOVES. SELKIRK DIRECT-TEMP SYSTEM SECU

Initial InstallationQUALIFIED INSTALLERS ONLYVerticalTerminationStorm CollarFlashingRound SupportBox/Wall ThimbleCeiling FirestopPipelengthPipelengthC

HORIZONTAL INSTALLATION:STEP 1. Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the