SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R I E S
Maintenance And ServiceQUALIFIED INSTALLERS ONLYGLASS DOOR REMOVAL:Blower / FanGas & ElectricalTray CompleteBurner Top withGrate AttachedLog Suppo
Maintenance And ServiceFUEL CONVERSION:TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLYPlease read and understand these instructions before installi
12Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 12), rotate it counter-
Initial InstallationWARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon
14Initial InstallationCheck draft with a matchor smoke in a " (6 mm)tube located here.MINIMUM FIREPLACE SIZE:Description of Fireplace Dimension
Initial InstallationQUALIFIED INSTALLERS ONLYDIRECT VENT MODEL:WARNING: This appliance has been designed to draw room air for proper heat circulation
16 DV Only: Maximum height allowed for the vent is 35ft(10.67m).Install sealed throat connector or flashing to preventleakage of room a
NOTE: If the Sienna unit is pulled out of its installation, and the vent air intake system is disconnected for any reason, ensure that the vent-
18Initial InstallationQUALIFIED INSTALLERS ONLYELECTRICAL REQUIREMENTS:The fan is thermostatically controlled and it will not operate if the a
Initial InstallationQUALIFIED INSTALLERS ONLYGAS LINE CONNECTION: Warning: Only persons licensed to work with gas piping may make the necessary gas co
2FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must b
Initial InstallationQUALIFIED INSTALLERS ONLYCONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE:Direct VentConnector AssemblyFresh AirInlet Cove
21Secondary InstallationFigure 30: Filler panel with trim installation.INSTALLATION OF SURROUND PANEL:The Sienna must have one of the panels installed
Secondary InstallationLOG SET AND EMBER INSTALLATION:NOTE: The logs are fragile and should be handled gently.The placement of the logs is not arbitrar
23Secondary InstallationFigure 34. Third Stage Log Set Installation.Figure 36. Fifth Stage Log Set Installation.Figure 35. Fourth Stage Log Set Ins
Secondary InstallationFigure 37. Sienna complete log set-up with embers burning.NOTE: While the glass is still removed, it is recommended that the gas
25Secondary InstallationREMOVING THE BRICK PANEL:The brick panel set is fragile, handle with extreme care.The brick panel set comes pre-installed. The
Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas c
27Parts List- Unit ComponentsReplacement parts must be purchased from an ENVIRO dealer.Reference # Part Description Part #1 120°F Ceramic Fan Temperat
Parts Diagram - ComponentsSIENNA - ComponentsOctober 200428
29Parts Diagram - BurnerSIENNA - BurnerOctober 2004
Table of Contents3Safety Precautions...2Table of C
Parts List - OptionsReference NumberOption DescriptionPart Number1AThe Cottage Trim Kit - Gold 50-5481A The Cottage Trim Kit - Pewter 50-5491A The C
31Parts Diagram - OptionsSIENNA - OptionsOctober 2004
WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to t
33Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs
Warranty19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a
35Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________
DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially
SpecificationsRATING LABEL LOCATION:The rating label is located under the control panel and is attached to a rectangular metal sheet that is chained t
6Specifications151/16"(383 mm)301/2"(775 mm)With Trim333/16"(343 mm)Without Trim33" (338 mm)205/8"(523 mm)223/4"(577 mm)
7WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.PIL
8Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before OperatingTURN OFF UNIT:Flip switch to OFF to turn off
9Maintenance And ServiceWarning: Failure to position the parts in accordance with this manual, or failure to use only parts specicall
Kommentare zu diesen Handbüchern