Enviro DV50DX Bedienungsanleitung

50-741SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R

Maintenance And ServiceCLEANING DECORATIVE SURFACES:Painted and porcelain faces should be wiped with a damp cloth periodically. If a plated face has b

11Maintenance And ServiceBURNER AND FAN REMOVAL:1. Remove brick liners, see steps 1 to 4 in SECONDARY INSTALLATION - CERAMIC BRICK LINER REMOVAL.2.

Maintenance And ServiceFUEL CONVERSION:TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLYPlease read and understand these instructions before installi

13Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 11), rotate it counter-

Gas InletElectrical Line49"(1245mm)21/8"(54mm)73/8"(187mm)45"(1143mm)215/8"(549mm)Initial InstallationQUALIFIED INSTALLERS ON

507/8"(1292mm)723/8"(1838mm)45"(1143mm)131/2"(343mm)36"(914mm)11/4"(32mm)153/8"(391mm)213/4"(552mm)211/2"

Protector pad,cement board andfinishing material.501/8”(1273mm)345/8”(879mm)Min 16”(406mm)461/2”(1181mm)33/8”(86mm)Min 393/4”(1010mm)33/8”(86mm)Cement

It is not necessary to install a mantle, but if one is desired it is important to follow the guidelines shown in Figure 21. Top of un

1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.2 In accordance with the current ANSI Z223.1 NFPA 54, National Fu

Flue Pipe AdaptorWall FramingWall ThimbleFire StopExhaust 4" Flex PipeCombusion Air 6 5/8" Flex PipeWire SpacersHorizontal Vent Termination1

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must be

through the outside wall far enough to connect onto the vent termination cap.10. Apply a bead of Mill-Pac Black sealant to the top section of the Ø4”

21Table 4: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).Direct Vent GSDirect-Temp Secure Vent Ameri Vent DirectDescripti

22Initial InstallationQUALIFIED INSTALLERS ONLYVENTING:This replace has been tested and certied for use with SIMPSON DURAVENT DIRECT VENT TYPE “GS”

Note: 0,0 representsa 90° bend directlyoff the top of the unit.543210' (0m)0' (0m)5' (1.52m)10' (3.05m)4' (1.22m)15' (4.

Wall framingHorizontal wallterminationWall thimblefire stopExhaustflex pipeCombustion airouter pipeElbowInitial InstallationQUALIFIED INSTALLERS ONLYH

25Initial InstallationQUALIFIED INSTALLERS ONLYStep 3. To install the Round Support Box/Wall Thimble in a at ceiling, cut a 10 inch (25.4 c

Initial InstallationQUALIFIED INSTALLERS ONLYSTEP 5. Cut hole in the roof centered on the small hole placed in the roof from Step 2. The hole should

27NOTES: (1) If an offset is necessary in the attic to avoid obstructions, it is important to support the vent pipe every 3 feet

For the rst 24 inches (610 mm) of ducting,  inch (13 mm) of clearance is required. After 24 inches (610 mm), the duct can be run w

29Initial InstallationQUALIFIED INSTALLERS ONLYELECTRICAL REQUIREMENTS:The replace must be electrically connected and grounded in accordance w

Table of ContentsSafety Precautions...2Tab

Initial InstallationGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to t

31LOG SET AND EMBER INSTALLATION:The placement of the logs is not arbitrary. If they are positioned incorrectly, the ames can be “pinched” and will n

Secondary InstallationFar Left LogFar Right LogFigure 43: The rst log to be placed is the front right log. The back end has a hole that sits on

33Secondary InstallationFront, Right ofCenter, LogLedgeFigure 48. Final Log Set ArrangementFront, Left ofCenter, LogBack Right LogFront Left LogTwo S

Figure 49: Once the logs are in place the embers can be placed onto and around the burner to create a realistic look. Bags of ceramic ber embers and

35TroubleshootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas

Parts List - ComponentsReference NumberDescription Part Number1 120°F (49°C) Ceramic Fan Temperature Sensor EC-0012 S.I.T. Nova Valve Convertible 50-1

37Parts Diagram - ComponentsDV50DX - ComponentsNovember 2004

Parts List- OptionsReference NumberOptions Part Number1The Lodge - Painted Black Face With Plated Brushed Nickel Louvres & Knobs50-7022 The Chale

39Parts Diagram - Options1234

DIRECT VENT ONLY: This type is identied by the prex DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec

WarrantySherwood Industries Ltd. is the manufacturer of the VistaFlame line of heating products. At Sherwood Industries, our commitment to the highest

415. As this is a heating appliance, some changes in colour of surface nishes may occur. This is not a aw and as such is not covered under this warr

Warranty22. Any statement or representation of VistaFlame products and their performance contained in VistaFlame advertising, packaging li

43Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

Main ventdiameter 61/2"The center of the ductinghook-ups are 103/16"from the center of themain vent.Gas/electricalinlets are thesame on both

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.PILO

7Warning: Incorrect venturi adjustment may lead to improper combustion, which is a safety hazard. Contact the dealer if there is any concern about

8Operating InstructionsBURNER LIGHTING:A) Make sure the pilot is lit.B) Turn gas control knob COUNTER CLOCKWISE to ON.C) Flip the burner swi

Maintenance And ServiceROUTINE MAINTENANCE:At least once a year, run through the following procedures to ensure the system is clean and working proper