Enviro EG40-071 Bedienungshandbuch Seite 1

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R I E S

Maintenance And ServiceFUEL CONVERSION:Figure 8: Removing valve cap.5. Convert the burner orice(s):a) Remove the main burner orice with a  inch de

11Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 9), rotate it counter-c

Initial InstallationQUALIFIED INSTALLERS ONLYWARNING: Operation of this heater when not connected to a properly installed and maintained venting syste

VENTING:This model must have a vent opening in the rear of the unit. Conrm this and also check that the label on the right side panel door states “V

TERMINATION:             Figure 13: Height of Vertical Termi

15STRAIGHT VERTICAL INSTALLATION:Figure 15: Straight vertical installation. This basic venting conguration shown are rough guidelines only. F

ELECTRICAL REQUIREMENTS:The ENVIRO EG40 will operate without electrical power. This model has a millivolt gas control, which uses the pilot ame to ge

Initial InstallationGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to t

CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may

19Secondary InstallationCAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED.Place the log set into the rebox. Locate each log

2FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must b

Trouble Shooting20Problem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas

21Parts ListReference NumberPart Description Part Number1 120 °F (49 °C) Ceramic Temperature Sensor EC-0012 220 °F (104 °C) Ceramic Spill Switch EC-0

Parts ListReference NumberPart Description Part Number15 Side Panel EG40-086 16 BV Stove Top EG40-087Firebox Bafe EG40-088Stove Top Bafe BV EG40-0

23Parts Diagram - ChassisEG 40 Body (Chassis)July 2004

Parts Diagram - Gas Tray & DoorEG40 Gas Tray & Door AssembliesJuly 20042892110243561171217272625424

25WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to

Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs o

2719. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a aw and

28Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

Table of Contents3Safety Precautions...2Table of Contents...

BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a

5SpecificationsDIMENSIONS:25"(635 mm)21"(533 mm)121/2"(318 mm)45/8"(117 mm)291/8"(740 mm)Shipping Weight 256 lbs (116 kg)Figu

Operating InstructionsFOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.LIGHTING INSTRUCTIONS:61. STOP! Read the safety information above on this label

ThermopileThermocoupleFigure 4: Gas Valve.Figure 3: Pilot Burning.7• There is a separate venturies for each burner, see Figure 4.• Remove one

8Maintenance and ServiceAnnually check to ensure that your Venting system is clear. Periodically check the pilot and burner. Check to see that all the

Figure 7: Blower (Fan) Removal.1. Turn the unit off, allow it to cool down completely, and remove the door as shown in the MAINTENAN