Enviro C-10985 Bedienungsanleitung Seite 1

PELLET STOVEMiniPLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS CO

10Figure 10: Corner Installation. CORNER THROUGH WALL INSTALLATION:3" (75mm)3"(75mm)Wall thimblemanufacturedby pellet ventmanufacturer.Insta

InstallationHORIZONTAL EXHAUST THROUGH WALL INSTALLATION:Vent installation: install vent at clearances specified by the vent manufacturer.A chimney co

12Wall framingWall thimbleTermination capVertical sectionof vent pipeHorizontal framefor thimble90° elbowConcrete WallClean out teeWall framingWall th

                    

14InstallationHEARTH MOUNT INSTALLATION:Rain capStorm collarSeal plate (cover plate)Existing masonry flueVent pipe (single wallstainless flex pipe ors

InstallationEXTERIOR MOUNTED EXHAUST BLOWER (20-070):The Mini can be equipped with an externally mounted exhaust blower. This optional kit i

InstallationTYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - HORIZONTAL TERMINATION:Electrical Cable90° Elbow45°Elbow with Rodentscreen or

17Roof SheathingRain CapRoof FlashingRoof RaftersCeiling JoistsVent PipeExterior WallSheathingOutside VentTerminationInstallationTYPICAL THROUGH WALL

InstallationTHERMOSTAT INSTALLATION:If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the thermos

19If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly

2Introduction...3Ratin

InstallationOPTIONAL PANEL KIT:This kit must be installed before the unit is started. 20Figure 31: Screws at back of the cab side.Figure 29: Screws ab

21Installation123Figure 32: Installing Hopper Lid.Installing Hopper Lid:1. Attach the hopper brackets to the back of the unit with a screw in e

TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly.

23TroubleshootingüPoor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.üExhaust Tempera

Troubleshooting7. The convection blower will not function normally.üClean all grill openings at the back and below unit .üPress the fan button; does t

25Wiring DiagramConnectThermostatHereRedRedRedRedBrownBrownBrownBrownWhiteWhiteWhiteWhiteWhite115VWhite220VBlueWhiteWhiteOrangeOrangeOrangeOrangeYello

Parts ListReference Number Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 Auger Motor - 115V EF-0013 High Limit Temp S

27Parts ListReference Number Description Part Number 17 Firebox Panel Set with Insulation 50-116218 Side Louver 50-116319 Burn Pot 50-116620 Burn Pot

Parts Diagram - ComponentsMini - ComponentsApril 200528

29Parts Diagram - SteelMini - Steel ComponentsApril 2005

3Introduction* This manual is designed for the technician in conjunction with the owner’s manual. *RATING LABEL LOCATION:The rating label is located o

WarrantySherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrica

31NAME OF OWNER:_________________________________________ADDRESS:_____________________________________________________________________________________

4IntroductionELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical c

5InstallationDECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:1. Remove the right and left hand cabinet sides by loosening the three (3) T-20 T

6InstallationAPPLIANCE DIMENSIONS AND SPECIFICATIONS:Figure 2: Dimensions of Mini. 151/2"(393 mm)187/8"(481 mm)171/2"(444 mm)195/8"

7InstallationCLEARANCES TO COMBUSTIBLES:IMPORTANT: Attach the Mini’s Hearth Pad when installing the unit on a combustible floor. The supplied hearth p

fumes such as stairwells, covered breezeway, etc.2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shieldi

9EXHAUST AND INTAKE LOCATIONS:101/16"(255mm)61/8"(156mm)21/16"(53mm)Figure 8: Mini Inlet and Outlet Location. EXHAUSTBase of unit to ce