50-765PELLET STOVEMERIDIANSHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.PLEASE KEEP THESE IN
EXHAUST PASSAGES (season)Removal of the firebox backing for bi-annual cleaning (refer to Figure 5):• Open the door by lifting the handle, remove
InstallationDECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:1. Check clearances to combustibles (see INSTALLATION - CLEARANCES TO COMBUSTIBLES - FREES
321/2"(826mm)247/8"(632mm)243/4"(629mm)InstallationDIMENSIONS - FREESTANDING:Figure 8: Meridian Freestanding Dimensions. 233/4"(60
Minimum6" (150mm)This pellet stove requires floor protection. The floor protection must be non-combustible, extending beneath the stove the full
InstallationCLEARANCES TO COMBUSTIBLES - FIREPLACE INSERT:The fireplace insert must be installed into a masonry fireplace. This model includes a surro
Ground wire directlyconnected to metal chassis.Hearth PadFlooringSteel Frame1/4" Lag boltssecurely fastenedFigure 17: Mobile Home Install Mountin
EXHAUST Freestanding InsertBase of unit to center of flue 18 ” (473 mm) 9 1/16” (229 mm)Side of unit to center of flue 6 11/16” (170 mm) 6
fumes such as stairwells, covered breezeway, etc.2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shieldi
Figure 22: Corner Installation. 3" (7.5 cm)3"(7.5 cm)Fresh Air IntakeWall thimblemanufacturedby pellet ventmanufacturer.InstallationCORNER T
Exhaust Tube3" (75mm) or 4" (100mm)"PL" or "L" ventWall Thimble45° Elbow with screenor Termination CapFresh Air IntakeHi
Table of ContentsIntroduction...
Wall framingWall thimbleTermination capVertical sectionof vent pipeHorizontal framefor thimbleClean out tee90°elbow Concrete WallWall fr
Rain cap - ensure cap is atleast 2 feet (610mm) abovethe roof at the lowest pointStorm collarRoof flashingRoof rafterFire stop withSupport CollarCeili
InstallationOUTSIDE VERTICAL INSTALLATIONS - FREESTANDING:To accomplish a outside vertical pipe installation, follow steps 1 through 5 in the “INSIDE
Rain capStorm collarSeal plate(cover plate)Existing masonryflueVent pipe (singlewall stainless flexpipe or solid PLvent)Fireplace damperlocationClean
InstallationINSTALLATION WITH EXTERIOR MOUNTED EXHAUST BLOWER - FREESTANDING:The MERIDIAN can be equipped with an externally mounted exhaust
TO SUPPLY POWER TO THE EXHAUST BLOWER:Install an amour coated electrical cable from the exhaust blower housing, through the wall thimble, and attach t
InstallationTHROUGH WALL VERTICAL INSTALLATION WITH EXHAUST BLOWER - FREESTANDING:Refer to INSTALLATION - INSTALLATION WITH EXTERIOR MOUNTED EXHAUST B
A noncombustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to
InstallationASSEMBLY AND INSTALLATION OF INSERT SURROUND PANELS - FIREPLACE INSERT:INSTALLATION AND REMOVAL OF CONTROL PANEL IN THE SURROUND PANEL
Figure 42: Installed Surround Panel. 6. Place the second side of the trim on the surround panel in the same manner used on the first
IntroductionPELLET QUALITY:Pellet quality is important, please read the following:Your enviro pellet stove has been designed to burn wood pellets only
InstallationPLATED TRIM INSTALLATION:TO AVOID PERSONAL INJURY DO NOT REMOVE OR REPLACE TRIMS WHEN PELLET STOVE IS HOT! REMOVAL OF SIDE TRIMS:When stov
TOOLS REQUIRED: ●11/32” socket or wrenchREMOVAL OF DOOR COVER:When stove is off and cool, open the door. Remove the four (4) #8 hex nuts around th
2. Open the right cab side to expose thermostat wires and disconnect. Install 18 gauge (see WIRING DIAGRAM) or heavier wire through the grommet
The slider damper is located behind the left cab side. The door must be open for the cab side to be removed on all models. On freestanding model loo
TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly.
Troubleshootinghose from vacuum switch. Check exhaust vacuum readings by placing the open end of the vacuum hose on a Magnahelic Gauge (readings must
Troubleshooting 6. The 200 °F ( 93 °C) high limit temperature sensor has tripped. üReset sensor and determine cause – was it convection blower fail
ConnectThermostatHereRedRedRedRedBrownBrownBrownBrownWhiteWhiteWhiteWhiteWhite115VWhite220VBlueWhiteWhiteOrangeOrangeOrangeOrangeYellowYellowGreyGreyG
Reference Number Description Part Number1 120 °F (49 °C) Ceramic Fan Temperature Sensor EC-001Domestic Power Cord - 115V EC-0422 Auger Motor - 115V EF
Reference Number Description Part Number23 Louver Bar Set - Gold 50-65523 Louver Bar Set - Pewter 50-65623 Louver Bar Set - Antique Copper 50-65724 Bu
IntroductionIMPORTANT SAFETY DATA:Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow
MERIDIAN - Freestanding Steel PartsDecember 2004Parts Diagram - Freestanding Steel40
MERIDIAN - Insert Steel PartsDecember 2004Parts Diagram - Insert Steel41
MERIDIAN - ComponentsDecember 2004Parts Diagram - Components42
WarrantySherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrica
NAME OF OWNER:_________________________________________ADDRESS:_______________________________________________________________________________________
IntroductionASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be on a non-com
Operating InstructionsAUTOMATIC SAFETY FEATURES:Your pellet Stove has the following safety features:A) The stove will shut off when the fire go
Operating InstructionsOPERATING YOUR PELLET STOVE:PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed correctly agai
2-3 Days / Weekly Semi-annually or 2 Tons of FuelBurn Pot and Liner Exhaust VentAsh Pan Fresh air Intake TubeInside Firebox Blower MechanismsDoor Gla
ASH PAN AND DOOR GASKETS (weekly)After extended use the gasketing may come loose. To repair this, glue the gasketing on using high-tempe
Kommentare zu diesen Handbüchern